Bioplastics were developed to overcome environmental problems that are difficult to decompose in the environment. This study analyzes Thai cassava starch-based bioplastics' tensile strength, biodegradability, moisture absorption, and thermal stability. This study used Thai cassava starch and polyvinyl alcohol (PVA) as matrices, whereas Kepok banana bunch cellulose was employed as a filler. The ratios between starch and cellulose are 10:0 (S1), 9:1 (S2), 8:2 (S3), 7:3 (S4), and 6:4 (S5), while PVA was set constant. The tensile test showed the S4 sample's highest tensile strength of 6.26 MPa, a strain of 3.85%, and a modulus of elasticity of 166 MPa. After 15 days, the maximum soil degradation rate in the S1 sample was 27.9%. The lowest moisture absorption was found in the S5 sample at 8.43%. The highest thermal stability was observed in S4 (316.8°C). This result was significant in reducing the production of plastic waste for environmental remediation.

The well-known phenomenon of phase separation in synthetic polymers and proteins has become a major topic in biophysics because it has been invoked as a mechanism of compartment formation in cells, without the need for membranes. Most of the coacervates (or condensates) are composed of Intrinsically Disordered Proteins (IDPs) or regions that are structureless, often in interaction with RNA and DNA. One of the more intriguing IDPs is the 526-residue RNA-binding protein, Fused in Sarcoma (FUS), whose monomer conformations and condensates exhibit unusual behavior that are sensitive to solution conditions. By focussing principally on the N-terminus low-complexity domain (FUS-LC comprising residues 1–214) and other truncations, we rationalize the findings of solid-state NMR experiments, which show that FUS-LC adopts a non-polymorphic fibril structure (core-1) involving residues 39–95, flanked by fuzzy coats on both the N- and C-terminal ends. An alternate structure (core-2), whose free energy is comparable to core-1, emerges only in the truncated construct (residues 110–214). Both core-1 and core-2 fibrils are stabilized by a Tyrosine ladder as well as hydrophilic interactions. The morphologies (gels, fibrils, and glass-like) adopted by FUS seem to vary greatly, depending on the experimental conditions. The effect of phosphorylation is site-specific. Simulations show that phosphorylation of residues within the fibril has a greater destabilization effect than residues that are outside the fibril region, which accords well with experiments. Many of the peculiarities associated with FUS may also be shared by other IDPs, such as TDP43 and hnRNPA2. We outline a number of problems for which there is no clear molecular explanation.

The simplest way to account for the influence of diffusion on the kinetics of multisite phosphorylation is to modify the rate constants in the conventional rate equations of chemical kinetics. We have previously shown that this is not enough and new transitions between the reactants must also be introduced. Here we extend our results by considering enzymes that are inactive after modifying the substrate and need time to become active again. This generalization leads to a surprising result. The introduction of enzyme reactivation results in a diffusion-modified kinetic scheme with a new transition that has a negative rate constant. The reason for this is that mapping non-Markovian rate equations onto Markovian ones with time-independent rate constants is not a good approximation at short times. We then developed a non-Markovian theory that involves memory kernels instead of rate constants. This theory is now valid at short times, but is more challenging to use. As an example, the diffusion-modified kinetic scheme with new connections was used to calculate kinetics of double phosphorylation and steady-state response in a phosphorylation-dephosphorylation cycle. We have reproduced the loss of bistability in the phosphorylation-dephosphorylation cycle when the enzyme reactivation time decreases, which was obtained by particle-based computer simulations.

Human papillomavirus (HPV) is recognized as the causative agent of cervical cancer in women, and it is associated with other anogenital and head/neck cancers. More than 120 types of HPV have been identified and many classified as high- or low-risk according to their oncogenic potential. One of its proteins, E6, has evolved to overcome the oncosuppressor functions of p53 by targeting this protein for degradation via interaction with the human ubiquitin-ligase E6AP. This study evaluates the correlation between the association strength of 40 HPV E6 types to the E6AP/p53 complex and the HPV oncogenesis risk using molecular simulations and machine and deep learning (ML/DL). In addition, a ML/DL-driven prediction is proposed for the HPV unclassified oncogenic risk type. The results indicate that thermodynamics play a pivotal role in the establishment of HPV-associated cancer and highlight the need to include some viral types in the HPV-related cancer surveillance and prevention strategies.

In this work, hydrogels based on semi-interpenetrating polymeric networks (semi-IPN) based on collagen-polyurethane-alginate were studied physicochemically and from different approaches for biomedical application. It was determined that the matrices in the hydrogel state are crosslinked by the formation of urea and amide bonds between the biopolymer chains and the polyurethane crosslinker. The increment in alginate content (0–40 wt%) significantly increases the swelling capacity, generating semi-crystalline granular structures with improved storage modulus and resistance to thermal, hydrolytic, and proteolytic degradation. The in vitro bioactivity results indicated that the composition of these novel hydrogels stimulates the metabolic activity of monocytes and fibroblasts, benefiting their proliferation; while in cancer cell lines, it was determined that the composition of these biomaterials decreases the metabolic activity of breast cancer cells after 48 h of stimulation, and for colon cancer cells their metabolic activity decreases after 72 h of contact for the hydrogel with 40 wt% alginate. The matrices show a behavior of multidose release of ketorolac, and a higher concentration of analgesic is released in the semi-IPN matrix. The inhibition capacity of Escherichia coli is higher if the polysaccharide concentration is low (10 wt%). The in vitro wound closure test (scratch test) results indicate that the hydrogel with 20 wt% alginate shows an improvement in wound closure at 15 days of contact. Finally, the bioactivity of mineralization was evaluated to demonstrate that these hydrogels can induce the formation of carbonated apatite on their surface. The engineered hydrogels show biomedical multifunctionality and they could be applied in soft and hard tissue healing strategies, anticancer therapies, and drug release devices.

This Editorial introduces the Biopolymers Special Collection on Peptide Nucleic Acid, available at the following link: https://onlinelibrary.wiley.com/doi/toc/10.1002/(ISSN)1097-0282.PNA I remember it like it was yesterday, even though it was more than 30 years ago. I was a graduate student at the University of Arizona (U.S.A.), sitting at my desk, eating lunch and perusing the latest issue of Science magazine. I came across an article about an intriguing new molecule called “polyamide nucleic acid” or PNA.[1] (We now define PNA as “peptide nucleic acid,” which is a perfectly fine name, except that PNA technically is not a peptide, it is not found in the nucleus and it is not an acid!) My Ph.D. thesis research had nothing to do with nucleic acid chemistry, but I still found the article fascinating, as the authors—Peter Nielsen, Michael Egholm, Rolf Berg, and the late Ole Buchardt at the University of Copenhagen (Denmark)—reported the ability of PNA to bind complementary DNA targets via a novel strand-invasion mechanism. The exceptionally high affinity of PNA for its targets, its resistance to natural degradation pathways and its fidelity to the Watson–Crick rules for base pairing sparked an intense level of excitement in both the fundamental science and the applications of PNA that continues to this day. Reading that paper certainly triggered my interest in nucleic acids and motivated me to seek out a postdoctoral position in the field. Two years later, I joined the laboratory of Gary Schuster at the University of Illinois (U.S.A.) where, by way of a happy accident, I had the good fortune to begin working with PNA through collaboration with Peter Nielsen's laboratory. 29 years later, my lab continues to work with this amazing molecule and its descendants. That paper changed my life! In this Special Collection of Biopolymers, we have gathered original research and review articles that highlight the ongoing evolution of PNA—both its structure and its applications. Backbone modifications that enhance affinity, nucleobase modifications that promote cell uptake, new applications in biosensing and self-assembly, and advances in targeting non-canonical structures, such as double-stranded RNA all demonstrate the versatility of PNA. While the original structure of PNA bedeviled researchers because of technical issues, for example aggregation, the next generation of PNAs have overcome these challenges. Moreover, the exploitation of PNA's peptide-like character via incorporation of amino acid side chains into the backbone, distinguishes PNA from other members of the nucleic acid alphabet soup, for example, LNA, that are more closely related to the natural biopolymers DNA and RNA. We hope you enjoy reading these articles and that you will return from time to time as we plan to take advantage of the dynamic nature of a virtual Special Collection to add more contributions in the future. Who knows what is in store for PNA, but the seemingly endless varieties that chemists are producing and the innovative new applications that scientists and biotechnologists continue to develop give great optimism that the PNA universe will continue to expand from the Big Bang of the 1991 paper.

Non-viral gene carriers have shown noticeable potential in gene delivery because of limited side effects, biocompatibility, simplicity, and the ability to take advantage of electrostatic interactions. However, the low transfection rate of non-viral vectors under physiological conditions is controversial. This study aimed to decrease the transfection time using a static magnetic field. We used self-assembled cationic polysaccharides based on dextran–stearic acid–spermine (DSASP) conjugates associated with Fe3O4 superparamagnetic nanoparticles to investigate their potential as gene carriers to promote the target delivery. Our findings illustrate that the magnetic nanoparticles are spherical with a positive surface charge and exhibit superparamagnetic behavior. The DSASP–pDNA/Fe3O4 complexes offered a strong pDNA condensation, protection against DNase degradation, and significant cell viability in HEK 293T cells. Our results demonstrated that although conjugation of stearic acid could play a role in transfection efficiency, DSASP magnetic carriers with more spermine derivatives showed better affinity between the amphiphilic polymer and the negatively charged cell membrane.

Circadian clocks are intracellular systems that orchestrate metabolic processes in anticipation of sunrise and sunset by providing an internal representation of local time. Because the ~24-h metabolic rhythms they produce are important to health across diverse life forms there is growing interest in their mechanisms. However, mechanistic studies are challenging in vivo due to the complex, that is, poorly defined, milieu of live cells. Recently, we reconstituted the intact circadian clock of cyanobacteria in vitro. It oscillates autonomously and remains phase coherent for many days with a fluorescence-based readout that enables real-time observation of individual clock proteins and promoter DNA simultaneously under defined conditions without user intervention. We found that reproducibility of the reactions required strict adherence to the quality of each recombinant clock protein purified from Escherichia coli. Here, we provide protocols for preparing in vitro clock samples so that other labs can ask questions about how changing environments, like temperature, metabolites, and protein levels are reflected in the core oscillator and propagated to regulation of transcription, providing deeper mechanistic insights into clock biology.

The redeposition of lignin to the fiber surface after organosolv pretreatment was studied using two different reactor types. Results from the conventional autoclave reactor suggest that redeposition occurs during the cooling down stage. Redeposited particles appeared to be spherical in shape. The size and population density of the particles depends on the concentration of organosolv lignin in the cooking liquor, which is consistent with the hypothesis that reprecipitation of lignin occurs when the system is cooled down. The use of a displacement reactor showed that displacing the spent cooking liquor with fresh cooking liquor helps in reducing the redeposition and the inclusion of a washing stage with fresh cooking liquor reduced the reprecipitation of lignin, particularly on the outer fiber surfaces. Redeposition of lignin was still observed on regions that were less accessible to washing liquid, such as fiber lumens, suggesting that complete prevention of redeposition was not achieved.

The regulation of the biodegradation rate of 3D-regenerated silk fibroin scaffolds and the avoidance of premature collapse are important concerns for their effective applications in tissue engineering. In this study, bromelain, which is specific to sericin, was used to remove sericin from silk, and high molecular weight silk fibroin was obtained after the fibroin fibers were dissolved. Afterwards, a 3D scaffold was prepared via freeze-drying. The Sodium dodecyl sulfate–polyacrylamide gel electrophoresis results showed that the average molecular weight of the regenerated silk fibroin prepared by using the bromelain-degumming method was approximately 142.2 kDa, which was significantly higher than that of the control groups prepared by using the urea- and Na2CO3-degumming methods. The results of enzyme degradation in vitro showed that the biodegradation rate and internal three-dimensional structure collapse of the bromelain-degumming fibroin scaffolds were significantly slower than those of the two control scaffolds. The proliferation activity of human umbilical vein vascular endothelial cells inoculated in bromelain-degumming fibroin scaffolds was significantly higher than that of the control scaffolds. This study provides a novel preparation method for 3D-regenerated silk fibroin scaffolds that can effectively resist biodegradation, continuously guide cell growth, have good biocompatibility, and have the potential to be used for the regeneration of various connective tissues.

Polygonati rhizoma (PR), a traditional medical and edible product, is rich in polysaccharides and exhibits physiological activity, including antioxidant, hypoglycemic and hypolipidemic properties. Neutral polysaccharides have been reported to be one of the main active ingredients of Polygonatum, with many of these fractions being responsible for the biological activity. This behavior was shown to be closely connected to the chemical structure, monosaccharide composition, and glycosidic bond type. There are few reports on the chemical constituents of the neutral polysaccharides from different sources of PR. In this study, neutral polysaccharides of PR from four different regions of China (Chun'an (Zhejiang), Xixia (Henan), Danfeng (Shanxi), and Pan'an (Zhejiang)), named CAZJ, XXHN, DFSX, and PAZJ, respectively, were isolated by anion-exchange and gel-permeation chromatography. Structures of the four polysaccharides were investigated. The results showed that all of them were mainly glucose and mannose, while the monosaccharide composition and content of polysaccharides from different sources varied. The molecular weights of CAZJ, XXHN, DFSX, and PAZJ were 14.119, 22.352, 18.127, and 15.699 kDa, respectively. Infrared spectra illustrated the existence of α-glycosidic bond and β-glycosidic bond in the polysaccharides. CAZJ, XXHN, and DFSX possessed a pyranose ring structure, whereas PAZJ had a furanose ring structure. Congo red test indicated that XXHN, DFSX, and PAZJ had a triple-helix structure. X-ray diffraction showed that the polysaccharides consisted of crystalline and amorphous regions. All four polysaccharides exhibited different degrees of antioxidant and hypoglycemic activities with a dose-dependent manner in the 1.0–10.0 mg/mL concentration range. Correlation analysis revealed that the bioactivities of polysaccharides was significantly related to monosaccharide composition, uronic acid, and protein content. The results suggested that neutral polysaccharides could be used as potential natural antioxidants and hypoglycemic agents for functional and nutraceutical applications.

This work reports synthesis of pH-responsive alginate/chitosan hydrogel spheres with the average diameter of 2.0 ± 0.05 mm, which contain cefotaxime that is an antibiotic of the cefalosporine group. The spheres provided the cefotaxime encapsulation efficiency of 95 ± 1%. An in vitro release of cefotaxime from the spheres in the media that simulate human biological fluids in peroral delivery conditions was found to be a pH-dependent process. The analysis of cefotaxime release kinetics by the Korsmeyer–Peppas model revealed a non-Fickian mechanism of its diffusion, which may be related to intermolecular interactions occurring between the antibiotic and chitosan. Conductometry, UV spectroscopy, and IR spectroscopy were used to study complexation of chitosan with cefotaxime in aqueous media with varied pH, characterize the composition of the complexes, and calculate their stability constants. The composition of the cefotaxime–chitosan complexes was found to correspond to the 1.0:4.0 and 1.0:2.0 molar ratios of the components at pH 2.0 and 5.6, respectively. Quantum chemical modeling was used to evaluate energy characteristics of chitosan–cefotaxime complexation considering the influence of a solvent.

Many species of pathogenic gram-positive bacteria display covalently crosslinked protein polymers (called pili or fimbriae) that mediate microbial adhesion to host tissues. These structures are assembled by pilus-specific sortase enzymes that join the pilin components together via lysine-isopeptide bonds. The archetypal SpaA pilus from Corynebacterium diphtheriae is built by the CdSrtA pilus-specific sortase, which crosslinks lysine residues within the SpaA and SpaB pilins to build the shaft and base of the pilus, respectively. Here, we show that CdSrtA crosslinks SpaB to SpaA via a K139(SpaB)-T494(SpaA) lysine-isopeptide bond. Despite sharing only limited sequence homology, an NMR structure of SpaB reveals striking similarities with the N-terminal domain of SpaA (NSpaA) that is also crosslinked by CdSrtA. In particular, both pilins contain similarly positioned reactive lysine residues and adjacent disordered AB loops that are predicted to be involved in the recently proposed “latch” mechanism of isopeptide bond formation. Competition experiments using an inactive SpaB variant and additional NMR studies suggest that SpaB terminates SpaA polymerization by outcompeting NSpaA for access to a shared thioester enzyme–substrate reaction intermediate.

Perturbations in the native structure, often caused by stressing cellular conditions, not only impair protein function but also lead to the formation of aggregates, which can accumulate in the cell leading to harmful effects. Some organisms, such as plants, express the molecular chaperone HSP100 (homologous to HSP104 from yeast), which has the remarkable capacity to disaggregate and reactivate proteins. Recently, studies with animal cells, which lack a canonical HSP100, have identified the involvement of a distinct system composed of HSP70/HSP40 that needs the assistance of HSP110 to efficiently perform protein breakdown. As sessile plants experience stressful conditions more severe than those experienced by animals, we asked whether a plant HSP110 could also play a role in collaborating with HSP70/HSP40 in a system that increases the efficiency of disaggregation. Thus, the gene for a putative HSP110 from the cereal Sorghum bicolor was cloned and the protein, named SbHSP110, purified. For comparison purposes, human HsHSP110 (HSPH1/HSP105) was also purified and investigated in parallel. First, a combination of spectroscopic and hydrodynamic techniques was used for the characterization of the conformation and stability of recombinant SbHSP110, which was produced folded. Second, small-angle X-ray scattering and combined predictors of protein structure indicated that SbHSP110 and HsHSP110 have similar conformations. Then, the chaperone activities, which included protection against aggregation, refolding, and reactivation, were investigated, showing that SbHSP110 and HsHSP110 have similar functional activities. Altogether, the results add to the structure/function relationship study of HSP110s and support the hypothesis that plants have multiple strategies to act upon the reactivation of protein aggregates.

Specific recognition of DNA base sequences by proteins is vital for life-cycles of all organisms. In a large number of crystal structures of protein–DNA complexes, DNA conformation significantly deviates from the canonical B-DNA structure. A key question is whether such alternate conformations exist prior to protein binding and one is selected for complexation or the structure observed is induced by protein binding. Non-canonical base pairs, such as Hoogsteen base pairs, are often observed in crystal structures of protein–DNA complexes. We decided to explore whether the occurrence of such non-canonical base pairs in protein–DNA complexes is induced by the protein or is selected from pre-existing conformations. Detailed quantum chemical calculations with dispersion-corrected density functional theory (DFT-D) indicated that most of the non-canonical base pairs with DNA bases are stable even in the absence of the interacting amino acids. However, the G:G Hoogsteen base pair, which also appears in the telomere structure, appears to be unstable in the absence of other stabilizing agents, such as positively charged amino acids. Thus, the stability of many of the non-canonical base pair containing duplexes may be close to the canonical B-DNA structure and hence energetically accessible in the ground state; suggesting that the selection from pre-existing conformations may be an important mechanism for observed non-canonical base pairs in protein–DNA complexes.

In recent times mucoadhesive drug delivery systems are gaining popularity in oral cancer. It is a malignancy with high global prevalence. Despite significant advances in cancer therapeutics, improving the prognosis of late-stage oral cancer remains challenging. Targeted therapy using mucoadhesive polymers can improve oral cancer patients' overall outcome by offering enhanced oral mucosa bioavailability, better drug distribution and tissue targeting, and minimizing systemic side effects. Mucoadhesive polymers can also be delivered via different formulations such as tablets, films, patches, gels, and nanoparticles. These polymers can deliver an array of medicines, making them an adaptable drug delivery approach. Drug delivery techniques based on these mucoadhesive polymers are gaining traction and have immense potential as a prospective treatment for late-stage oral cancer. This review examines leading research in mucoadhesive polymers and discusses their potential applications in treating oral cancer.

Before reaching their targets, sequence-specific DNA-binding proteins nonspecifically bind to DNA through electrostatic interactions and stochastically change their locations on DNA. Investigations into the dynamics of DNA-scanning by proteins are nontrivial due to the simultaneous presence of multiple translocation mechanisms and many sites for the protein to nonspecifically bind to DNA. Nuclear magnetic resonance (NMR) spectroscopy can provide information about the target DNA search processes at an atomic level. Paramagnetic relaxation enhancement (PRE) is particularly useful to study how the proteins scan DNA in the search process. Previously, relatively simple two-state or three-state exchange models were used to explain PRE data reflecting the target search process. In this work, using more realistic discrete-state stochastic kinetics models embedded into an NMR master equation, we analyzed the PRE data for the HoxD9 homeodomain interacting with DNA. The kinetic models that incorporate sliding, dissociation, association, and intersegment transfer can reproduce the PRE profiles observed at some different ionic strengths. The analysis confirms the previous interpretation of the PRE data and shows that the protein's probability distribution among nonspecific sites is nonuniform during the target DNA search process.

Translocation of positively charged cell penetrating peptides (CPP) through cell membrane is important in drug delivery. Here we report all-atom molecular dynamics simulations to investigate how a biphosphate salt in a solvent affects the interaction of a CPP, HIV-1 Tat peptide with model dipalmitoylphosphatidylcholine (DPPC) lipid bilayer. Tat peptide has a large number of basic arginines and a couple of polar glutamines. We observe that in absence of salt, the basic residues of the polypeptide get localized in the vicinity of the membrane without altering the bilayer properties much; polypeptide induce local thinning of the bilayer membrane at the area of localization. In presence of biphosphate salt, the basic residues, dressed by the biphosphate ions, are repelled by the phosphate head groups of the lipid molecules. However, polar glutamine prefers to stay in the vicinity of the bilayer. This leads to larger local bilayer thickness at the contact point by the polar residue and non-uniform bilayer thickness profile. The thickness deformation of bilayer structure disappears upon mutating the polar residue, suggesting importance of the polar residue in bilayer deformation. Our studies point to control bilayer deformation by appropriate peptide sequence and solvent conditions.

The Panspermia hypothesis posits that either life's building blocks (molecular Panspermia) or life itself (organism-based Panspermia) may have been interplanetarily transferred to facilitate the origins of life (OoL) on a given planet, complementing several current OoL frameworks. Although many spaceflight experiments were performed in the past to test for potential terrestrial organisms as Panspermia seeds, it is uncertain whether such organisms will likely “seed” a new planet even if they are able to survive spaceflight. Therefore, rather than using organisms, using abiotic chemicals as seeds has been proposed as part of the molecular Panspermia hypothesis. Here, as an extension of this hypothesis, we introduce and review the plausibility of a polymeric material-based Panspermia seed (M-BPS) as a theoretical concept, where the type of polymeric material that can function as a M-BPS must be able to: (1) survive spaceflight and (2) “function”, i.e., contingently drive chemical evolution toward some form of abiogenesis once arriving on a foreign planet. We use polymeric gels as a model example of a potential M-BPS. Polymeric gels that can be prebiotically synthesized on one planet (such as polyester gels) could be transferred to another planet via meteoritic transfer, where upon landing on a liquid bearing planet, can assemble into structures containing cellular-like characteristics and functionalities. Such features presupposed that these gels can assemble into compartments through phase separation to accomplish relevant functions such as encapsulation of primitive metabolic, genetic and catalytic materials, exchange of these materials, motion, coalescence, and evolution. All of these functions can result in the gels' capability to alter local geochemical niches on other planets, thereby allowing chemical evolution to lead to OoL events.

The biological functions of polysaccharides are influenced by their chemistry and chain conformation, which have resulted in various functional applications and new uses for polysaccharides in recent years. Sacran is an intriguing ampholytic polysaccharide with several key properties such as metal adsorption, anti-inflammatory nature, and transdermal drug-carrying capacity. It has an extremely high molecular weight over 107 g/mol, which is much higher than those of the previously reported microbial polysaccharides. In particular, it has a remarkable self-orienting characteristic over a large length scale, which could produce a bundle with twisted morphologies from the nanoscale to the microscale with diameters of ~1 μm and lengths of >800 μm. In this review, morphological variations, as well as novel self-organization and hierarchical self-assembly are comprehensively discussed. Sacran fibers deform into various forms, such as two- and three-dimensional flexible fibers and micro–nano fragments, during their evaporation. The self-assembly and disassembly of the sacran are explained in terms of the preparation process and factors that influence the morphology. This review will pave the way for the development of novel modules such as humidity-sensitive actuators, micro-patterned cell scaffolds, and uniaxially oriented membranes.